Representing the worlds most Innovative electronic products and solutions
This prestigious award recognises the break through in EDLC Capacitor development and the launch of mass produced 3V series of products covering from 3 Farad to 600 Farad and rated at -40c~+65c.
This seemingly small step increases capacitance density by 23% and a cell reduction of 10% for hi density applications such as Solar and Wind energy harvesting, Electric and Hybrid Vehicles thus reducing costs, weight and size in this important market for renewable and recycling energy.
Compared with batteries, super capacitors have longer life time, faster charging and discharge times with 1000 times longer cycle life than Batteries. Vinatech Hy-Cap products have one-tenth of the energy of batteries, but delivers over 10 times the power due to the ultra low ESR characteristics, so, many designers are moving towards Ultra Capacitors as their alternative energy storage devices.
Vinatech appointed BT2000 as their UK & Ireland Representative and Distributor earlier this year. The hi-density technology covers a high capacitance range of 0.75 Farad to 900 Farad in EDLC and Hybrid P-EDLC options. During 2013 BT2000 expect further boundary breaking announcements with the extension of their range for markets such as UPS, SSDs Toys & DVRs, Electric & Hybrid vehicles and renewable energies along with, Actuators, AMR and products for communications media.
We are back from the southern Manufacturing & Electronics Exhibition 2013 where we successfully launched a number of new Lines.
Thank you to everyone who stopped by to see us.
For more Photo's visit our Facebook page http://www.facebook.com/BT2000.co.uk
BT2000 will be launching Innovative new lines at Southern Manufacturing
and Electronics Exhibition 2013
on the 13th & 14th February meet the BT2000 team at stand B20.
FIVE | Farnborough | Hants | GU14 6XL
For Free entry visit www.industrysouth.co.uk
For more information about us and our booth please call us on telephone number (0)1189 324600
|Omnidirectional Tilt & Vibration Sensor|
For more information please Contact us on (0)1189 324600 or Email using Sales@bt2000.co.uk
Memsic are now offering new Development Boards for all actively promoted products.
These Development Boards provide a convenient and easy way to evaluate and prototype with MEMSIC Accelerometers and Magnetometers.
All Boards come with the sensor mounted as shown on the MXR7305VF-B board below
For more information on the Development Boards products Click here for Accelerometer or Magnetometer Prototyping Boards
Alternativly Contact us on (0)1189 324600 or Email using Sales@bt2000.co.uk
Adactus have unveiled a new 4G antenna. The ADA0040 is multiband HiGain Antenna covering the known 4G bands and also current 2G & 3G Frequencies This LTE blade Antenna has a swivel connector, offering flexible positioning for most M2M applications.
This antenna features:
During this years NAPFM - Blue Light Fleet Exhibition BT2000 Launched, in partnership with PCTEL,
the New Dual GPS Ultra-Wideband Mobile Antenna.
This multi-band antenna Covers a wide range including TETRA, 700-2500 MHz LTE/3G, 2.3-2.5 GHz WiFi broadband wireless frequencies and dual GPS L1 tracking.
The MC66-W Terminal is probably the lowest cost on the market today
Utilising Cinterions Modem the product is compatible with standard AT Commands
BT2000 met with Cellergy in Israel following the launch of the new CLK & CLC ranges.
The CLC range has gained enormous interest and the factory production levels are at an all time high. CLCs are ideally suited for Coin Cell battery life extension in ISM applications
Memsic the leading supplier of AMR MEMS Sensors have launched the smallest Magnetometer on the market to date.
Just 2mm square the MMC3316 offers a 3 Axis I2C interfaced device with superb sensitivity and low power features.
For more information click here
Vincotech has launched a competitive range of Gen6 IGBT power modules amongst a number of new features to their growing range
Click here to view the full brochure
Pericom have announce the PT8A2823 a Li-ON Battery charging IC, they have a range of USB charging products for this growing requirement.
This will be a great opportunity for you to meet the Vincotech team and discuss with their FAE specialists about products for your next Project. Vincotech have increased capacity to meet growing demands ,introduced new technologies, so come and meet the team to learn more about their benefits. For a FREE Vincotech pass just click here to register http://www.vincotech.com/news/tradeshows.html
To ensure that you can meet the engineers please indicate the date and time you intend to be there so we can reserve a guaranteed slot. If we miss you, please ask for Stephane who looks after the UK.
Vincotech, a member of the Mitsubishi group will be launching new initiatives at PCIM.These will include new housings, new chips, topologies and software.
Vincotech have recently launched a new series of Mini Skips. Offering a truly competitive option to existing models in the market.
If you are attending, please visit us. We look forward to seeing you.
To meet Market demands PCTEL have developed a Multiband Antenna for the Homeland security markets One Box requirements
This Combination antenna offers Tetra, GPS, 4G/LTE (including 3G, GPRS &2G) along with Wifi connectivity in a rugged rubberised radome.
For more information click here
Cellergy is happy to announce the launching today of a new product series (CLK) of increased capacitance (double capacitance as compared to the general purpose CLG series). The increased capacitance version will be available for its 17x17.5 mm and 28x17.5 mm foot print products.
This series of products is based on the Cellergy's patented screen printing process. Cellergy supercapacitors are suited for pulse applications and are frequently used in conjunction with batteries to assist in delivering energy to the load. The new super capacitors will offer a better solution for applications which require higher capacitance and lower voltage drop.
The A2200 GPS modules enable fastest acquisition and tracking with the latest SiRFstarIV technology. In any case the module fully answers the demand for lowest power consumption with – amongst other features – SiRFawareTM technology. The removal of jammers does not only facilitate designs of new products, but guarantees operation even in hostile environments. Highest sensitivity, during acquisition or while tracking, allows for use in many different environments and under toughest conditions.
The CLC range has been developed for applications requiring low leakage , especially for Coin Cell applications, reducing the
leakage levels from the existing miniature 12mm square CLG range by half to 1.5uA per cell.
Samples are available now.
Broadband Technology 2000 (BT2000) Ltd are proud to announce that they have been appointed as the Pericom Semiconductor representative for the UK & Eire. The Pericom portfolio includes Timing & Frequency control products, Analogue, Digital & ASSP switches, PCIe Products, Power Management and Home Appliance ICs.
Since Pericom's acquisition of SaRonix & eCera, they have become one of the major suppliers of discrete crystals, crystal oscillators, voltage control and temperature compensated crystal oscillators, as well as fully integrated multiple output clock ICs.
Leveraging their own in-house crystal and IC design, Pericom provide the best-in-class crystal (Xtal) and crystal oscillators (XO) to suit all design requirements.
The wide range of crystal and crystal oscillators provide:
Output frequencies ranging from kHz to 800MHz
Complete portfolio of outputs
Complete portfolio of XO with standard XO, VCXO, TCXO
Multiple voltage ranges from 1.0V to 3.3V (even legacy 5V)
Large portfolio of SMT package options to fit your footprint requirements
Designed for the consumer market the MMC328xMS (3 x 3 x 1.2mm) Magnetic Sensor from Memsic is proving to be exceptionally popular. Following on from this popularity Memsic have been developing an even smaller version of their which is 2 x 2 x 1.2 mm. This new device is the MMC328xMA, Ultra Small Magnetic Sensor with I²C Interface. The MMC328xMA Magnetic Sensor from Memsic is suitable for the following applications: Electronic Compass, GPS Navigation, Position Sensing and Magnetometry.
3977D through Hole (Permanent) Mount 28dB GPS Antenna
Proving to be popular and dependable, with it’s clear and consistent GPS signal reception.
The 3977D has proven itself time after time, it’s a through hole (permanent) mount GPS antenna providing a high out-of-band rejection performance. The 3977D has a custom designed ceramic patch element for maximum signal reception and minimal loss-of-lock when GPS Conditions are less than ideal.
The 3977D 28dB permanent mount antenna is designed to have multiple applications such as:
Cellular Base Station Clocking and Timing
Fleet Management & Telematics
Marine Vessel installations
Permanent Mount Vehicle installations
WLAN Wireless Broadband Clocking and Timing
The 3977D has a number of features that make it ideal for use in most environments:
Weather proof, all-plastic, non-corrosive, IP67, low profile enclosure
¾ inch thru-hole or bracket mount
Voltage range: 2.7 to 5.5 V
High gain: 28 dB
Low noise figure: 1.5 dB
High out-of-band signal rejection
Operating temperature of -40° to +85°C
1575.42 MHz ± 10 MHz
The PCTEL 397xD range of antennas comes with a range of features including up to 40dB gain and dual SAW filters for High-Rejection.
Please do not hesitate to contact us for more information.
Wave Soldering of Cellergy supercapacitors (SCs) to PCB's was tested for through-hole printed circuit assemblies only. The challenge of wave soldering for supercapacitors with aqueous electrolyte as well as organic electrolyte is the high ambient temperature in the wave soldering bath and preheating oven. Electrical performance of the SCs was measured before and after the Wave Soldering.
Wave soldering is a large-scale soldering process by which electronic components are soldered to a PCB to form an electronic assembly. The process is much faster, thus can lower the cost of assembly and can create a
higher quality product than manual soldering of components. The name is derived from the use of waves of molten solder to attach metal components to
The process uses a tank (or bath) to hold a quantity of molten solder; the components are inserted into the PCB and the loaded PCB is passed across
a pumped wave or waterfall of solder. The solder wets the exposed metallic leads protruding from the bottom of the PCB, creating a reliable mechanical
and electrical connection.
Wave soldering is largely used where SMT is not suitable (e.g. large power devices and high pin count connectors), or where simple through-hole technology prevails (certain major appliances).
The A2035-H is Maestro Wireless Solutions answer to the most critical challenges in the GPS market: high integration, high performance, and a reduce time to market. The combination of a fully enhanced SiRFStar IV GPS engine and a custom-made high directional patch antenna ease engineers integration job in tough electrical environment.
All outstanding features of the SiRFStar IV GPS engine are immediately available: fast, responsive location experience with high sensitive navigation engine tracking down to -163dBm; breakthrough micro power technology, the A2035-H only requires between 50 to 500μA to maintain hot start capability and active jammer remover.
The A2035-H fully addresses the demand for extreme low power operation and ultra fast TTFF. Its highest sensitivity, allows for use in the most demanding conditions.
“Our A2035-H GPS antenna module is a great achievement from the R&D team. Apart from its high reliability and attractive features, it also will ensure to our customer a faster time to market as well as strong RF performances” commented Xavier DUPONT Managing Director of the Fargo Telecom Group.
All Maestro Wireless Solutions products come with detailed manuals and easy-to-use evaluation boards. The A2035-H operates in the full temperature range from -40°C to +85°C.
Sample and development kit are immediately available through Broadband Technology. production ramp-up will follow in November 2011. You can also visit Maestro Wireless Solutions at CTIA Enterprise & Applications 2011, booth 356, October 11-13 at the San Diego Convention Center in California.
In addition to the Maestro 100CDMA certified by Aeris, Sprint, Verizon, the GPRS Maestro 100evo also get FCC and PTCRB approval making it available worldwide.
The Maestro 100 is a full range of GPRS/EDGE Rx or CDMA packet data modem with a universal RS232 interface for easy integration into any M2M solution. The Maestro 100CDMA features a full TCP/IP stack and support gpsOne for location aware application. The industrial power supply supporting voltage range from 9 to 60V DC. The Maestro 100evo is a GPRS/EDGE Rx programmable modem supporting OpenAT and can be easily set-up through Maestro’s Configuration Software, a Windows based application that let you easily setup and test your modem. This tool includes important features such as automatic and self recovery TCP/UDP connection or remote program update via DOTA.
Both devices come in an industrial metal casing supporting extreme temperature with a din-clip mount, easy to integrate into the most demanding industrial environment.
The Maestro 100evo is already a reference in Europe and Asia in the metering and industrial automation market. “The launch of the Maestro 100 will strengthen our presence in the US market” said Olivier Bernard, Maestro Wireless’ Vice-President of Business Development. “ the M2M market in the US has increasingly matured and the market demands easy to install and cost-effective devices for mass-deployment. The Maestro 100 was designed to be the new benchmark in the US M2M marketplace.”
Device are immediately available through Broadband Technology, or you can visit Maestro Wireless Solutions at CTIA Enterprise & Applications 2011, booth 356, October 11-13 at the San Diego Convention Center in California.
German based manufacturer of Digital Pressure Sensors, SensDev UG, has appointed Broadband Technology 2000 ltd to market their innovative range of MEMS Pressure sensors in the UK & Ireland.
SensDev, based in Burgstaedt, Germany, have developed their innovative pressure solutions over a long period and have now developed a unique technology much further advanced than similar technologies.Typical Applications for SensDev Digital Pressure sensor technology include the Utility markets, Industrial automation & production, test & measurement, medical and automotive markets
The latest SensDev SCPB Series of amplified analogue and 15 bit digital serial output (via I²C or SPI) pressure sensors (measuring range of 0.6mbar to 25bar) uses state of the art silicon micro machined (MEMS) pressure sensors in conjunction with stress free packaging techniques to provide cost effective temperature compensated (-40C to +125C) pressure sensors. Automotive specifications are available on request covering -55c~+150c. SensDev have a wide supply voltage range from 3.3V to 40V and features include fast response times of 0.56ms to 20ms which are factory selectable. All EMC filtering is on-board and various cable lengths / types and housings are available on request.
The SensDev SCPB I2C feature communicates as a slave digitally via an I²C-bus interface and delivers (within less than 1ms) continual serial 15bit pressure data after powering up the sensor. It answers on I²C-bus Master requests. Slave addresses are individually programmable.
SensDev production utilises a flexible manufacturing process enabling customer's specific requirements to be produced within short lead times with each unit having its own individual serial number, printed and readable via the EEPROM. Quality levels are second to none.
Cellergy announce a new Super Capacitor. This new part, the CLG03P250L28
GPS Manufacturer Maestro have launched new firmware for the SiRF IV GPS Module
GPS Manufacturer Maestro have launched new firmware for the SiRF IV GPS Module The newly released 4.1.0 offers users many new enhancements Switchable from 1Hz to 5Hz navigation update rate. Higher Accuracy Lower Power - Improved Micro-power mode (consumption is now less than 125uA) 3 days Extended Ephemeris SGEE extension from 7 to 14 days Improved TTFF Data ready port (can reduce host power consumption) With the Super sensitivity of the A2100 these added features must make this unit the best on the market today